Pegatron Ipmsb-h61: Manual
Connecting the front panel connectors correctly is crucial for turning on the computer. Below is the typical pinout for the JFP1 header on this Pegatron board: HDD LED Power (+) Pin 3 (HD_LED-): HDD LED Power (-) Pin 5 (RST_SW-): Reset Switch (-) Pin 7 (RST_SW+): Reset Switch (+) Pin 2 (PWR_LED+): Power LED (+) Pin 4 (PWR_LED-): Power LED (-) Pin 6 (PWR_SW+): Power Switch (+) Pin 8 (PWR_SW-): Power Switch (-) Pin 9/10: Usually empty or used for BIOS/Speaker. 5. BIOS/BIOS Update The board uses an AMI BIOS.
PCIe x16 graphics slot, PCIe x1 slots, and Audio header.
2x DDR3 DIMM slots, Dual Channel, max 8GB (4GB per DIMM), support for DDR3 1066/1333 MHz. Expansion Slots: 1x PCIe x16 (for graphics cards). 1x PCIe x1. 2x PCI slots. Storage: 4x SATA II 3.0 Gb/s connectors. Audio: Realtek ALC662 6-channel High Definition Audio. LAN: Realtek RTL8111EL Gigabit Ethernet (10/100/1000 Mbps). Form Factor: Micro-ATX. 2. Layout and Internal Connectors (Motherboard Manual) pegatron ipmsb-h61 manual
Below is a summary of the board's capabilities, compiled from various technical sources and hardware probes:
: Insert matching DDR3 sticks into both slots to enable dual-channel mode. Always press down firmly until the side clips snap into place. Power Connectors Connecting the front panel connectors correctly is crucial
| Feature | Specification | | :--- | :--- | | | Micro-ATX (mATX), 24.4 x 21.4 cm | | Socket | LGA 1155 | | Chipset | Intel H61 Express | | CPU Support | Intel Core 2nd Gen (Sandy Bridge) & 3rd Gen (Ivy Bridge)* | | Memory | 2 x DDR3 DIMM slots; Supports dual-channel DDR3 1066/1333 MHz; Up to 8GB (non-ECC) | | Expansion Slots | 1 x PCIe 2.0 x16 (for graphics card) 1 x PCIe 2.0 x1 2 x PCI | | Storage | 4 x SATA II (3Gb/s) ports | | Audio | Realtek ALC662, 5.1-channel High Definition Audio | | LAN | Realtek RTL8111E Gigabit Ethernet (10/100/1000 Mbit) | | Back Panel I/O | 1 x PS/2 Mouse, 1 x PS/2 Keyboard 1 x D-Sub (VGA), 1 x DVI-D 4 x USB 2.0 1 x RJ45 LAN port 3 x Audio jacks | | Internal Connectors | 24-pin ATX power, 4-pin CPU power, 4 x SATA II, 1 x CPU fan, 1 x chassis fan, front panel header, front audio header, COM header, LPT header, and USB 2.0 headers for additional ports |
: It includes four SATA 3Gb/s (SATA II) connectors. Networking is handled by a Realtek RTL8111EL Gigabit LAN controller, and audio is provided by a 6-channel Realtek ALC662 codec. Rear Panel and Internal Connectors BIOS/BIOS Update The board uses an AMI BIOS
Press the key repeatedly during the initial POST screen to enter the AMI BIOS setup. Clearing CMOS: To reset BIOS settings to factory defaults: Turn off the PC and unplug the power cord. Locate the CLEAR CMOS jumper (near the battery).